Arduino Mega and RAMPS case

This is heavily based on http://www.thingiverse.com/thing:863076 but is a complete rework and redraw to accommodate an 80mm fan, more ventilation slots and 5mm more height.

Other changes include the square 'hoops' along each side to cable tie cables to, the 12mm high standoffs, 3mm mounting bolts holes (recessed to prevent short circuits) increased size of the M3 nut holders and larger cable exits.

10/12/2016 - I uploaded an alternative back end for the box as this one gives better ribbon cable access for the LCD display and cable access generally.

30/06/2017 - I've uploaded a new set of sides. These are 15mm taller than the originals to allow more electronics to be crammed into the RAMPS case. They are identified as v1.6 (taller) in the file listing.

Other parts designed for my printers include:

• http://www.thingiverse.com/thing:1959901 (GT2 belt clamp (Prusa Y-axis)
• http://www.thingiverse.com/thing:1937232 (Arduino Mega and RAMPS v1.4 case)
• http://www.thingiverse.com/thing:1905409 (Prusa i3 steel 10mm upgrade)
• http://www.thingiverse.com/thing:1959974 (Prusa i3 Steel Y-axis motor mount)
• http://www.thingiverse.com/thing:1991116 (Prusa i3 Steel X-carriage)
• http://www.thingiverse.com/thing:1991117 (E3D Chimera / Cyclops mount)
• http://www.thingiverse.com/thing:1994413 (dual E3D Thermocouple amplifier board - housing)
• http://www.thingiverse.com/thing:1090661 (Belt driven Bowden extruder with 1:2.5 reduction)
• http://www.thingiverse.com/thing:896676 (enclosure for SevenSwitch FET)
• http://www.thingiverse.com/thing:922455 (8mm Z-axis leadscrew bearing holder)
• http://www.thingiverse.com/thing:922309 (Z-axis NEMA 17 adjustable endstop bracket)
• http://www.thingiverse.com/thing:899607 (cable chain)
• https://www.thingiverse.com/thing:2334269 (LCD housing)
• https://www.thingiverse.com/thing:2377049 (PSU cover)
• https://www.thingiverse.com/thing:2395715 (Chimera & Zesty Nimble drive cable spacer)
• https://www.thingiverse.com/thing:2407651 (Chimera Zesty Nimble X-axis set for i3 clone)
• https://www.thingiverse.com/thing:2436869 (A dummy NEMA 17 motor to hold the 5mm shaft)
• https://www.thingiverse.com/thing:2748978 (A Duet WiFi housing)
• https://www.thingiverse.com/thing:2749324 (A layer fan for the Smart Effector)
• https://www.thingiverse.com/thing:2814068 (A Sannce I21AG mount for 3D printers)
• https://www.thingiverse.com/thing:2844881 (A cooling duct for a Noctua 40mm fan on a Duet Smart Effector)
• https://www.thingiverse.com/thing:2846955 (A quiet BerdAir type pump mount)
• https://www.thingiverse.com/thing:3333609 (A Raspberry Pi case with 40mm fan)

For avoidance of doubt, this item is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License. See http://creativecommons.org/licenses/by-nc-sa/4.0/ for more details.